Table of Contents 1. SAFETY INSTRUCTIONS... 1 1.1 WORK AREA SAFETY .
8 through menu and submenu items in menu mode. H. LEFT Arrow LED Lighting Adjusting Button – Uses Left arrow button to decrease LED brightness in t
9 3. Installation and Connection 3.1 The Imager Head and Cable Installation To use the tool, the imager head and cable must be connected to the displ
10 Fig. 6 Fig. 7 For MV400 (with 5.5mm imager head): The two accessories include
11 To insert a Micro SD card into the Micro SD card slot, make sure the contacts are facing towards slot and the angled portion of the card is facing
12 4. Battery Charging Precautions To reduce the risk of serious injury, read these precautions and the label on charger’s surface carefully before u
13 4.3 Charger Inspection Before using, inspect the charger and correct any problems. Set up charger according to these procedures to reduce the risk
14 to start charging. The battery will begin charging automatically. While the battery is charging, the charging indicator light will be red
15 5. Operation Instructions Always wear safety eye protection to protect your eyes against dirt and other objects. Follow operation instructions
16 5.2 Operation Precautions Use the tool only as directed. Do not operate the tool unless the user’s manual has been read thoroughly and proper tr
17 Use only accessories that are recommended by the manufacturer for the tool. Dry your hands when operating the tool or charging the battery.
5.6 ICONS ... 29 5.7 SOFTWARE UPDATE ...
18 Turn on the power and make sure the tool model through the splash screen and then display the live screen. If the tool does not work well aft
19 inspection. The Imager head and cable were waterproof to a depth of 3m (10'), Greater depths may cause leakage into the imager head and ca
20 Always handle the tool with care. It is not shock-resistant. Do not disassemble the tool beyond what is shown in the manual. Doi
21 A brightness indicator bar will be displayed on the screen as you adjust brightness. (Fig. 12) Fig. 12 5) Zooming Simply press UP and DOWN
22 Fig. 14 Color or Monochrome In the Setup screen, select Color or Monochrome and press OK button, then the Color or Monochrome setting screen
23 Fig.16 If you want to format the media (in most cases, it is the Micro SD card), use the LEFT/RIGHT button to select Yes, then press OK button to
24 7) Entering the Secondary Settings Screen While in the Primary Settings Screen (Fig. 14), select Advanced Settings from Setup and then pr
25 Language In the Advanced Settings screen, select Language and press OK button, then the Language setting screen will appear. (Fig. 20) Englis
26 exit without saving changes. 8) Capturing a Photo When in the live screen, make sure the camera icon is present at the top left portion of the scr
27 Fig. 23 It may take few seconds to save the captured video to internal memory. The tool could capture a video approximately 80s without
1 1. Safety Instructions To prevent personal injury or damage to vehicles and/or the scan tool, read this instruction manual first and observe the f
28 Fig. 25 While viewing these photos and videos, press OK button to select, and then the screen will display as below (Fig.26). The digit on the top
29 Fig. 27 Select Yes to confirm your selection and press OK button to delete the file, or select No to cancel the command and press OK button to exi
30 inserted into the tool. 4) Still Camera – Indicates the tool is operating in still camera mode. 5) Video Camera – Indicates the tool
31 6. Troubleshooting Symptoms Possible Reason Solutions Display is on, but does not show image. Cable connection is loose. Check and reattach.
32 7. Warranty Information
2 1.3 Personal Safety Do not use the tool while tired or under the influence of drugs, alcohol, or medications. A moment of interruption can result
3 2. Description, Specifications and Tool Components 2.1 Description This premier Autel MaxiVideo TM MV400 digital videoscope is an ideal tool for
4 Weight 0.288kg(0.63lbs) Recording medium Micro SD card (Micro SD card is optional and not included) Image controls Zoom, low light vision Ligh
5 2.4 Tool Components and Ports The MaxiVideoTM MV400 comes with the following items: Note: Because of continuing improvements, actual product
6 6) DC Power Source Port – Connects the tool to the mains with the supplied charger to power on the tool or to charge battery. 7) Micro SD card S
7 2.5 Buttons and Controls Fig. 4 A. LCD Screen – Indicates still images and videos. B. Trash Can/Reverse Button – Deletes captured photos a
Commentaires sur ces manuels